spareparts.html

Accessories

CASE LUBE KIT (PAD TYPE) The most popular way to properly lubricate cases for resizing and case forming. The bottom side of the pad includes non-skid feet so it won’t skate all over your bench when you are using it. Kit includes 2 oz. plastic bottle of Redding Case Lube.
Redding Case Lube Kit
NO. 12012 ....$22.50
Case Lube Pad only
NO. 12010 ... $15.90

DEBURRING TOOL Removes burrs and bevels case mouths for easy bullet seating. Hardened precision ground flutes make clean, easy, chatter-free cuts. Accepts all cases from .17 to .45 caliber.
NO. 09000..$31.50

CASE PREPARATION KIT All the tools you need in one package for removing dirt and powder residue from the inside of case necks and primer pockets.

STUCK CASE REMOVAL KIT Sooner or later everyone does it. Too little case lubricant (or using ordinary oil) and the case seizes in the resizing die.

Kit comes complete with accessory handle, large and small primer pocket cleaners and three (3) case neck brushes to
handle all cartridges from .22 thru .45 caliber.
NO. 18000 . . . . . . . . . . . . . . . . . . . . . . $31.50
NO. 18005 Accessory Handle . . . . . . . . $9.00
NO. 99139 Large Pocket Cleaner . . . . . $5.70
NO. 99138 Small Pocket Cleaner . . . . . $5.70
NO. 99137 Large Neck Brush . . . . . . . . $4.20
NO. 99136 Medium Neck Brush . . . . . . $4.20
NO. 99136å Small Neck Brush . . . . . . . $4.20

Usually, the rim pulls off and it is almost impossible to remove the stuck case without damaging the die. This case removal kit provides an easy solution to your problems. Instructions included. NO. 22000 ..... $27.90

DIE SPACER KIT For use with combination die sets and all 7/8-14 reloading dies to quickly compensate for case length or make a no-crimp adjustment without the need to move the lock rings.

EXTENDED
SHELLHOLDER
Extended shellholders are required when trimming short cases under 1 1/2” O.A.L. They are machined to the same tolerances as our standard shellholders except they’re longer.
See Die Caliber Reference Chart for proper sizes.
NO. 115XX (specify shellholder #) . . . $18.60

The kit includes three spacers: (.062) No-crimp or partial resizing, (.125) 44 Spl/44 Mag spacer, (.135) 38 Spl/357 Mag spacer.
NO. 80901 ....$12.00

POWDER FUNNEL Nearly indestructible, super-tough Lexan™. Fits all cartridge cases from .22 to .45 caliber. Anti-static prevents powder from sticking.
NO. 13000 ..... $8.10

ORIGINAL FORMULA CASE LUBE Packaged in 2 oz. plastic squeeze bottle. Formulated for tough resizing and forming operations. Prolongs the life of your dies and simplifies reforming. There is a difference in case lubes!
NO. 21000.... $7.50

BALL HANDLE CONVERSION
Convenient, easy-to-attach conversion for those who prefer a ball handle on their reloading press. Fits the Redding BOSS and Turret Press as well as other reloading presses that use a 5/8" handle diameter. Easily attaches without machining or threading.
NO. 99175 .... $9.30

WATER SOLUBLE CASE LUBE Water soluble -- but contains no water, therefore it is not harmful to your brass or dies. Can be used with all dies for normal resizing, but is ideal for neck sizing and use with straight wall pistol cases. Clean, neat and easy to clean up. 2 oz. plastic squeeze bottle.
NO. 21011 .... $7.50

BENCH STAND
For convenient bench-top mounting of Redding Powder Measures. Will also fit all other Powder Measures with 7/8-14 thread mounting. This bench stand is not threaded; it is secured with a lock ring which enables you to rotate the measure to any desired position and permits quick dump of the reservoir.
NO. 06000 ..... $46.50

POWDER MEASURE RESERVOIRS Replacement powder reservoirs are available in three sizes with or without caps. The smallest shown is the same as originally supplied on your Redding powder measure.

Interesting Note: Our tests have demonstrated that powder measures show slightly improved accuracy when mounted in a bench stand securely fastened to a solid bench.

The intermediate is 7-1/2" overall length and the largest available is 10". These fit all models of Redding powder measures using a 2-1/8" O.D. reservoir.

DOUBLE “C” CLAMP Now available in two sizes. The original SAECO Double “C” Clamp was designed as a convenient way to secure the SAECO lubrisizer to a bench top. The newest model is the ideal size for clamping the Redding powder measure stand and case trimmer to a bench top.Both units will accommodate a bench thickness of up to 2-1/4". May be used to mount any number of tools. Handy items for any reloading room. Both units will accommodate a bench thickness of up to 2-1/4".

NO. 99130 Original Replacement Reservoir . . . . . $9.00
NO. 99333 Original Replacement Reservoir
with cap . . . . . $12.00
NO. 99157 7-1/2" Reservoir . . . . . $12.00
NO. 99165 7-1/2" Reservoir w/ cap . . . . . $15.00
NO. 99162 Long 10" Reservoir . . . . . $18.00
NO. 99167 Long 10" Reservoir with cap . . . . . $18.00
NO. 99101 Reservoir cap . . . . . $3.90

NO. 30120 Lubrisizer Clamp (2-3/8" inside fingers)...$31.50
NO. 30520 Bench Stand/Trimmer Clamp (1-5/8" inside fingers) .... $31.50

HODGDON
ANNUAL MANUAL
The ‘08 Manual features load data using Hodgdon, IMR & W-W powders plus articles by Layne Simpson, Charles Petty, Terry Wieland, Wayne Van Zwoll, Sheriff Jim Wilson and more.
NO. 05988 ....... $7.99

INGOT MOULDS The SAECO cast iron ingot mould will produce four easy-to-handle ingots. A perfect way to store blended alloys.
NO. 23000..$28.50

BACK TO HOME PAGE | BACK TO ONLINE CATALOG | BACK TO PARTS & ACCESSORIES